Description. Germany AWS DIN 1654-5 (1989) , DIN 17440 (1996) , DIN 17455 (1985) , DIN 17456 (1985) , DIN EN 10088-3 , DIN EN 10088-4 , DIN EN 10088-5 , DIN EN 10297-2 (2005) , DIN EN 10088-1 , DIN EN 10088-2 , DIN 17456 (1985) , DIN 5512-3 , DIN EN 10151 , DIN EN 10250-4 , DIN EN 10263-5 , DIN EN 10296-2 (2005) , 1.4016 Specialsteel Cold heading and cold extruding steels; technical Alloy Ergste 1.4016IM Technical InformationPAGE 1/2 PRECISION STRIP ERGSTE® 1.4016IM Ergste® 1.4016IM Categorization Ferritic stainless Chromium-Steel DIN EN 10088-2:1.4016, X6Cr17 ASTM A666/AISI:Type 430(USA) JIS G4305:SUS 430 (Japan) Technical properties Corrosion resistance:middle
BS EN 10088-2 is the material standard for stainless steel sheet, plate and strip for general purposes. A total of 97 stainless steel grades are listed, including 25 ferritic, 14 martensitic, 2 precipitation hardening, 44 austenitic and 12 austenitic-ferritic (duplex) grades. The chemical compositions of these stainless steels are shown in this article. Chemical resistance of Stainless steelResistance to general corrosion is usually classified as follows:0 = resistant to general corrosion (mass loss rate <0.1 g/h · m² corresponding to a corrosion rate < 0.11 mm thickness reduction/year) 1 = slight susceptibility to general corrosion, suitable for some applications (0.1 1 DECLARATION OF PERFORMANCE AND TEC-DOP-4003H 1. Identification code of the product-type 1.4016 EN 10088-4:2009 2. Type 1.4016 3. Product Hot Rolled Strip & Sheet of Corrosion Resisting Steel 4. Intended use Building Construction or Civil Engineering 5. The Notified Body:has conducted the first inspection and continuous surveillance according to the system:and issued the certificate:
EN 10088:Steel grades /numbers. EN 10088-1:2005 Stainless steels. List of stainless steels. EN 10088-2:2005 Stainless steels. Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes. EN 10088-3:2005 Stainless steels. Technical delivery conditions for semi-finished products, bars, rods, wire EN 10088-2 - Stainless Steel Tube Stainless Steel Pipe3.1 stainless steels definition in EN 10088-1 applies 3.2 corrosion resisting steels steels with at least 10,5 % Cr and max. 1,20 % C if theiresistanceto corrosion is of primary impotanee 3.3 product forms definitions in EN 10079 apply 3.4 types of heat-treatment definitions in EN SS EN 1.4016 Sheet, Plate, Coil Manufacturer, Supplier in Nov 26, 2018 · EN 10088-2:2005 Stainless steels. Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes:Thickness:0.4mm to 3mm (Cold Rolled process) 3mm to 35mm (hot rolled process) Length:2000mm, 2440mm, 3000mm, 5800mm, 6000mm, etc. Width :600mm, 1000mm, 1219mm, 1500mm, 1800mm, 2000mm, 2500mm, 3000mm, 3500mm, etc.
Ferritic corrosion resisting steel Materials Services Technology, Innovation & Sustainability Page 1/4 Steel designation Name Material No. X6Cr17 1.4016 Scope This data sheet applies to hot and cold-rolled sheets/plates and strips, semi-finished products, rods, wire, sections and bright products for general purpose. Application Stainless steelsEN 10088-1:2005. It supersedes BS EN 10088-1:1995 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/30, Stainless Steels, which has the responsibility to:This second edition of BS EN 10088-1 is a revised reference document containing chemical analysis and physical property data for 160 stainless Structural Design of Ferritic Stainless Steels1.4016 contains around 16.5% chromium, and has a greater resistance to corrosion than 1.4003. It is the most widely used ferritic stainless steel grade. The following grades can be described as special or stabilised ferritic grades, and are less widely available. They contain additional alloying elements such as
Chemical composition % of steel X6Cr17 (1.4016):EN 10088-2-2005. Elements not listed in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. Particular ranges of sulphur content may provide improvement of particular properties.