[email protected]

35L / 35 Non-alloy casting steel

Technological properties of the material 35L ( 35 ) . Linear shrinkage :2.2 - 2.3 %. Heat treatment of the material 35L ( 35 ) Normalizing 860 - 880 ° C, Tempering 600 - 630 ° C. Hardening 860 - 880 ° C, Tempering 600 - 630 ° C. Physical properties for grade 35L ( 35 ) T. E 10- 5. Difference between P355NL1 steel and P355NL2 steelDifference between P355NL1 steel and P355NL2 steel. The designation P355NL1 and P355NL2 steel shows that they are steel for pressure purposes (P) with minimum yield strength of 355 MPa (355) which is impact tested in the transverse direction at -20 deg C (NL1) and -40 deg C (NL2).

E355 / 1.0580 - SteelNumber - Chemical composition

Non-alloy quality steel Chemical composition of steel E355 (1.0580), Standards of steel E355 (1.0580) Mechanical Properties of steel E355 (1.0580) Equivalent grades of steel E355 (1.0580) steel E355 (1.0580) Tensile Strength, Elongation, Proof strength , Hardness EN 10028:3 P355NL1 and P355NL2 Brown McFarlaneIt has three steel grades (P275, P355, and P460) which indicate each grades minimum yield strength (in MPa) for plates 16 mm thick and below. These are further subdivided on the basis of impact testing (transverse) temperature:N and NH indicate impact testing at -20 deg C or above, NL1 at -40 deg C or above, and NL2 at -50 deg C or above. Grade S355NL, S355ML and Q345 Steel Differences steel S355ML:S355ML steel is normalized steel (fine grain steel) in EN10025-3:2004 standard. Its yield strength and tensile strength correspond to China's Q345 low alloy steel. Grade Q345:Q345 material is a kind of steel. Is a low alloy steel, widely used in bridges, vehicles, ships, construction, pressure vessels, special equipment, etc.

P355NL1 / 1.0566 - SteelNumber - Chemical composition

EN 10217-3:2002 Welded steel tubes for pressure purposes. Alloy fine grain steel tubes:EN 10253-2:2007 Butt-welding pipe fittings. Non alloy and ferritic alloy steels with specific inspection requirements Equivalent grades:Go here :Chemical composition % of steel P355NL1 (1.0566):EN 10028-3-2009 S355NL / 1.0546 - SteelNumber - Chemical composition Go here. Chemical composition % of steel S355NL (1.0546):EN 10025-3-2004. Nominal thickness =< 63 (mm) CEV max = 0.43. For long products the P and S content can be 0.005% higher. For railway application a maximum S content of 0.01% may be agreed at the time of enquiry and order. In sufficient other N-binding elements are present the minimum S355NL Steel Plates, S355NL Carbon and Low Alloy Dec 18, 2018 · S355NL steel plates are having greater yielding strength at a room temperature of about 355 MPA at 16mm and falling temperature at 250mm to 250 MPA. It is just a normalized. This grade steel is widely used for various applications. CHINA UNITED IRON AND STEEL LIMITED is having enough stock of S355NL steel plates to easily supply to all its

SSAB Laser 355C - Laser-cutting steel exceeding S355J2C+N

All products benefit from superior steel cleanliness, well balanced and consistent chemistry, optimized for laser cutting and narrow and consistent dimensional tolerances. Dimension Range. SSAB Laser® 355C is available in thickness 3.00 - 30.00 mm and widths up to 1860 mm as cut to length and 3300 mm as plate. Length up to 16 meters as cut to TABELLA DI COMPARAZIONE DELLE QUALITA'Europe Germany France United Kingdom U.S.A. U.S.S. EN 10025 :2004 EN 10025-2 :2004 EN 10155 :1993 EN 10155-2 :1993 EU 155:80 SEW 087 AFNOR A 35-502 BS 4360 ASTM Licence steel S235JOW 1.8958 S235JOW 1.8958 Fe 360 C KI E 24 W 3 S235J2W 1.8961 S235J2W 1.8961 Fe 360 D KI WTSt 37-3 E 24 W 4 S355JOWP 1.8945 S355JOWP 1.8945 Fe 510 C 1 KI E 36 W A 3 WR50A A W-Nr 1.3505 Bearing Steel 100Cr6-Din 17230 Alloy OTAI SPECIAL STEEL is 1.3505 bearing steel stockholders and suppliers from china. more 16 years experience in DIN W-NR 1.3505 steel plate, round bar, flat bar, square bar, pipe/tube supply. DIN W-NR 1.3505 bearing steel is a high quality Alloy Bearing steel, It belong to a high carbon, chromium containing low alloy steel.. 1.3505 Oil Quenched

Which steel grade is best equivalent to S355J2+N

Which steel grade is best equivalent to S355J2+N ? S355J2+N steel is one grade in EN10025-2 with low alloy.S355J2+N (minimum yield strength 355 MPa, Tensile 470 to 630 MPa,+N means plus Normalized when rolling,J2 means doing charpy V-notch impacting test @ -20 ).Which steel grade is best equivalent to S355J2+N ?--Xin S355J2+N steel is one grade in EN10025-2 with low alloy.S355J2N steel plate (minimum yield strength 355 MPa, Tensile 470 to 630 MPa,+N means plus Normalized when rolling,J2 means doing charpy V-notch impacting test @ -20 ).. Firstly we suggest steel grade equivalent S355J2+N is ship steel plate ASTM A131 GR.DH36 (minimum yield strength 355 MPa, Tensile 490 to 620 Mpa, heat treatment